Your source of photonics CAD tools

FIMMPROP

A bi-directional optical propagation tool

Grating-assisted colourless directional coupler

Simulation with OmniSim's FEFD and FDTD Engines and FIMMPROP software

This design won the Best Innovation Design competition of the 2012 Group IV Photonics conference, sponsored by Photon Design.

FIMMPROP and OmniSim were used to simulate the spectral response of a novel design of power coupler able to operate over a 100nm bandwidth, a much larger spectral range than conventional directional couplers.

This design, relying on the use of a dispersion compensating grating, was published by Robert Halir et al. [1] at the University of Malaga, and won the Best Innovation Design competition of the 2012 Group IV Photonics conference, sponsored by Photon Design.

Response of a standard coupler

Directional coupler: (left) conventional design
(right) dispersion engineered design with compensating grating. (source: [1])

The idea behind the design is the following: the bandwidth of directional couplers is limited by the modal dispersion, which results in strong variations of the ideal length of the coupler with wavelength. A standard evolution of coupler efficiency with wavelength can be seen in the plot below. This plot was obtained with FIMMPROP, with a simulation time of 25s for 64 points.

Coupling efficiency vs wavelength for conventional directional coupler

Spectrum of coupled power (dB) to the bar (blue) and cross (orange) output
waveguides for the conventional coupler (FIMMPROP); the length of the
coupler was set to 108um, giving equal power splitting at 1.55um.

Halir et al. used a sub-wavelength (lossless) grating to compensate for the modal dispersion. A picture of the design with and without the grating is show below. The grating pitch, duty cycle and the gap between the waveguides were optimised to obtain a 50/50 power splitter over the widest possible bandwidth.

The structure was modelled in 2D using FIMMWAVE's propagation tool FIMMPROP, as well as OmniSim's FEFD and FDTD engines. The three methods were found to be in excellent agreement with the published results and with one another.

The structure is shown below designed in FIMMPROP (top left). Note that the grey sections are references to the other sections; in particular the tapered region only needs to be modelled once with FIMMPROP's taper algorithm, speeding up calculation time considerably. The central section is a periodic section, which uses the component showed underneath as a period. In this case we used FIMMPROP's EME algorithm to model the grating but we could have also used its Rigorous Coupled Mode Theory (RCMT) engine.

Grating assisted directional coupler designed in FIMMPROP

(top left) Grating-assisted directional coupler designed in FIMMPROP,
relying on (bottom right) a separate component to design the individual period.

The structure is shown below designed in OmniSim. The periodic section is designed by repeating a sub-device periodically.

Grating assisted directional coupler designed in OmniSim

Grating-assisted directional coupler designed in OmniSim.

You can see the spectral evolution of transmitted power for the FIMMPROP and FDTD results in the plot below. The grating design offers an excellent splitting ratio over a much larger range of wavelength, providing the component with a much better bandwidth than the conventional directional coupler.

In addition, the grating allows us to strongly reduce the size of the directional coupler and the footprint of the component: without grating, the optimal length of the coupler would be 108um, whilst the grating allows us to reduce the length of the coupling region to ~25um.

Design of the coupler

Evolution of coupled power (dB) to the bar (blue) and cross (orange) output waveguides with wavelength.
Dashed lines represent the design without grating (from FIMMPROP).
Dotted lines correspond to the grating results obtained with EME, and solid lines to the grating results obtained with FDTD.

Simulation time: 12.5s per wavelength for FIMMPROP (300 modes) i.e. 13 mins for 64 points, 18 mins for the FDTD calculation (10nm grid) on an i7-2600 CPU.

References

[1] R. Halir, A. Maese-Novo, A. Ortega-Moñux, I. Molina-Fernández, J. G.Wangüemert-Pérez, P. Cheben, D.-X. Xu, J. H. Schmid and S. Janz, "Colorless directional coupler with dispersion engineered sub-wavelength structure", Optics Express, 20, 12, pp. 13470-13477 (2012)